Netgear WNDAP380Rv2 Manual de usuario Pagina 148
- Pagina / 152
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
148
ProSAFE Dual Band Wireless-N Access Point with RFID Support, WNDAP380R
channels and frequencies
defaults 125
selecting for 802.11a/na modes
29
selecting for 802.11b//jointfilesconvert/35013/bg/ng modes
27
channels, wireless spacing
25
Clear to Send (CTS) packets
83
CLI (command-line interface) commands
131
clients
associated, number of
115
DHCP, enabling
22
isolation, enabling
84
maximum number
85
monitoring
111
NTP, enabling
21
trusted
58
wireless separation, enabling
43, 50
collision detection and collision avoidance, CSMA
83
command-line interface (CLI) commands
131
community names and traps, SNMP
65
compliance, electromagnetic
127
configuration file, backing up or restoring
69
connectors and ports, rear panel
12
country, wireless location
20
CSMA (Carrier Sense Multiple Access)
83
CTS (Clear to Send) packets
83
cwMin (minimum contention window) and cwMax
(maximum contention window) values
86
D
data encryption
WEP
52
WPA and WPA2
55
data rates
802.11a mode
30
802.11b//jointfilesconvert/35013/bg modes
27
specifications for all modes
125–126
date and time, troubleshooting
122
defaults
channels and frequencies
125
DHCP gateway
24
factory settings, list of
127–130
factory settings, restoring
70
IP address
18, 127
ISP gateway
22
login password
18, 127
SNMP
64
subnet mask
22, 127
user name 18, 127
delivery traffic indication message (DTIM) interval
84
DHCP (Dynamic Host Configuration Protocol) client and
server
22–24
DNS (Domain Name System) servers
22–24
DTIM (delivery traffic indication message) interval
84
dual-band support (concurrent)
9
dynamic and static VLANs
50
Dynamic Host Configuration Protocol (DHCP) client and
server
22–24
E
EDCA (Enhanced Distributed Channel Access)
parameters
85–87
electromagnetic compliance
127
encryption
WEP
52
WPA and WPA2
55
environmental specifications
127
ESS (extended service set)
43
Ethernet cabling requirements
16
Ethernet packets and bytes, received and transmitted
115
extended service set (ESS)
43
F
factory default settings
list of
127–130
restoring
70
firmware
backing up
69
factory defaults
70
restoring from backup file
70
RFID module version, viewing
105
upgrading
67
wireless access point version, viewing
110
flash memory
66
fragmentation length
84
frequencies and channels
defaults
125
selecting for 802.11a/na modes
29
selecting for 802.11b//jointfilesconvert/35013/bg/ng modes
27
FTP traffic
advanced QoS
85
WMM QoS
61
G
gateways, ISP and DHCP 22–24
generating keys, WEP
52
Gigabit Ethernet (RJ-45) port
13
graphical user interface (GUI)
described
19
troubleshooting
119
- ProSAFE Dual Band Wireless-N 1
- WNDAP380R 1
- Trademarks 2
- Revision History 2
- Contents 3
- Chapter 4 Management 4
- Chapter 6 Monitoring 4
- Chapter 7 Troubleshooting 5
- What Is in the Box? 7
- System Requirements 8
- Key Features and Standards 8
- Key Features 9
- Networking 10
- Hardware Description 11
- Rear Panel 12
- Introduction 13
- Installation and Basic 14
- Configuration 14
- Ethernet Cabling Requirements 16
- Web Management Interface 19
- To configure time settings: 20
- Configure the IP Settings 21
- Ceiling Installation 31
- Wall Installation 35
- Desk Installation 38
- Wireless Configuration and 39
- Security 39
- Security Profiles 42
- Security Profile Concepts 43
- Form for 802.11b/bg/ng Modes 44
- Form for 802.11a/an Modes 45
- Configure Legacy 802.1X 52
- Figure 11. Legacy 802.1X 53
- Figure 12. WPA with RADIUS 53
- Figure 13. WPA2 with RADIUS 53
- Figure 15. WPA-PSK 54
- Figure 16. WPA2-PSK 54
- Management 63
- Enable Remote Management 64
- Web Browser Upgrade Procedure 67
- TFTP Server Upgrade Procedure 68
- Defaults 69
- Restore the Configuration 70
- Settings 70
- Default Configuration 72
- Enable the Syslog Server 73
- To enable a syslog server: 74
- To configure STP and VLANs: 80
- Configure Hotspot Settings 81
- To set up a hotspot server: 82
- To configure advanced QoS: 86
- 4. Click Apply 87
- Configure Wireless Bridging 88
- Advanced Configuration 100
- Configure RFID Settings 103
- To reboot the RFID module: 106
- To reset the RFID module: 106
- 3. Click Apply 107
- Monitoring 108
- View System Information 109
- Monitor Wireless Clients 111
- View the Activity Log 113
- Traffic Statistics 114
- Troubleshooting 116
- Basic Functioning 117
- Wireless-Capable Computer 118
- Check these items: 119
- Request timed out 121
- Problems with Date and Time 122
- Troubleshoot the RFID Module 122
- Supplemental Information 124
- Technical Specifications 125
- Factory Default Settings 127
- Command-Line Reference 131
- Numerics 147
Relacionado con productos y manuales para Puntos de acceso wlan Netgear WNDAP380Rv2
(28 paginas)
Puntos de acceso wlan Netgear WAB102 Guía de usuario
(49 paginas)
(49 paginas)
(43 paginas)
Puntos de acceso wlan Netgear WG602v3 Manual de usuario
(122 paginas)
(122 paginas)
Puntos de acceso wlan Netgear WG102 Manual de usuario
(110 paginas)
(110 paginas)
Puntos de acceso wlan Netgear MR814v2 Manual de usuario
(142 paginas)
(142 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales