Netgear WG102 Manual de usuario Pagina 20
- Pagina / 134
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
20 |
WG102-500, WGAP150 ProSafe™ 802.11g Wireless Access Point
1. Specify the fields in the Basic System Settings section of the Basic Settings screen (see
Figure 2-6) as explained in Table 2-1.
Table 2-1. Basic System Settings
Field Description
AP Name Assign a unique name to the wireless access point.The default name is NETGEAR.
The AP name can be retrieved through SNMP.
Location Assign a unique name to the location of the wireless access point.The default name is
site1. The site name can be retrieved through SNMP.
AP Mode Select one mode from the pull-down menu:
• Bridge. The wireless access point functions as a bridge, for example, between a
wired and a wireless network. This is the default setting.
• Router. The wireless access point functions as a router. When you select this
mode, the Management VLAN ID becomes inactive and the LAN settings appear at
the bottom of the Basic Settings screen (see “Configuring LAN Settings” on page
23).
Management
VLAN ID
The management VLAN can be active only when the wireless access point functions
as a bridge. Specify a VLAN ID from which the wireless access point can be managed.
The default setting is zero, which allows for management of the wireless access point
from any VLAN, and which prevents frames belonging to the Management VLAN from
being tagged with an 802.1Q header when sent over the trunk.
Domain Name Select an easily recognizable domain name to facilitate web management and the
redirection of HTTP requests.
Time Zone Select the time zone to match your location.
NTP Server If you want to use a Network Time Protocol (NTP) server, enter its host name.
Note: You must have an Internet connection to use an NTP server that is not on your
local network.L
STP Select the STP checkbox to enable the Spanning Tree Protocol (STP) to prevent path
redundancy. When the STP checkbox is selected, two more options appear on the
Basic Settings screen.
Bridge
Priority
Enter the priority for root switch election. The default is 32768.
Ethernet Path
Cost
Enter the best path cost from the switch to the root switch. The default
is 100.
2. Click Save or Save to Flash & Activate to save your settings.
Configuring IP Settings
To configure the IP settings:
1. Specify how the wireless access point acquires its IP address by making a selection
from the Server IP pull-down menu in the IP Settings section of the Basic Settings
screen (see Figure 2-7 on page 21):
• DHCP. The IP address, subnet mask, and the default gateway settings for the
wireless access point are acquired automatically from a Dynamic Host Configuration
- WG102-500, WGAP150 1
- ProSafe™ 802.11g Wireless 1
- Access Point 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Table of Contents 3
- 4 4
- Table of Contents 5
- Chapter 6 Troubleshooting 6
- Appendix B Related Documents 6
- Introduction 7
- Key Features 8
- 9
- System Requirements 10
- What’s In the Box? 10
- Hardware Description 11
- Table 1-1 12
- 13
- Ethernet Cabling Requirements 14
- 15
- Figure 2-1 16
- Figure 2-2 17
- Figure 2-3 17
- Web Interface Menu 18
- Settings 18
- System > Basic 19
- Configuring IP Settings 20
- Figure 2-7 21
- Table 2-3. PPPoE Settings 22
- Figure 2-8 22
- Configuring LAN Settings 23
- 24 24
- Figure 2-10 25
- 26 26
- Figure 2-11 27
- Figure 2-12 28
- 29
- 30 30
- 31
- 32 32
- 33
- Figure 3-1 34
- Security Profiles 35
- 36 36
- 37
- Figure 3-2 38
- Figure 3-3 39
- Configuring Static WEP 40
- Table 3-3 41
- Figure 3-5 41
- Table 3-2 41
- Table 3-4 42
- Figure 3-6 42
- Table 3-5 43
- Figure 3-7 43
- Figure 3-8 44
- Table 3-6 44
- Table 3-6 45
- Figure 3-9 46
- 47
- 48 48
- WAPI Certificates 49
- Figure 3-11 50
- Figure 3-12 51
- Figure 3-13 52
- Figure 3-14 53
- Figure 3-15 54
- Figure 3-16 55
- Table 3-9. Filter Settings 56
- Figure 3-17 57
- Figure 3-18 58
- Figure 3-19 59
- 60 60
- Managing Your Network 61
- Backing up the Configuration 62
- Restoring the Configuration 62
- 63
- Figure 4-2 64
- 65
- Figure 4-3 66
- Figure 4-4 67
- Viewing the Activity Log 68
- Figure 4-6 69
- Figure 4-7 69
- Viewing System Information 70
- Figure 4-8 71
- Table 4-1 71
- Table 4-1 72
- Table 4-2 73
- Figure 4-9 73
- Viewing Wireless Information 74
- Table 4-4 75
- Figure 4-11 75
- Figure 4-12 75
- Table 4-5 76
- Figure 4-13 77
- Configuring Remote Management 78
- Table 4-7 79
- 80 80
- Figure 4-15 81
- Figure 4-16 82
- Figure 4-17 83
- 84 84
- SNMP Remote Management 85
- Configuring SNMP Communities 86
- Figure 4-20 87
- Figure 4-21 87
- Configuring SNMP Users 88
- Figure 4-22 89
- Figure 4-23 89
- Configuring TR069 Operation 90
- Scheduling Management Tasks 91
- Figure 4-25 92
- 93
- 94 94
- Advanced Configuration 95
- Figure 5-1 96
- Figure 5-2 97
- 98 98
- Figure 5-3 99
- 100 100
- Figure 5-4 101
- Figure 5-5 102
- Figure 5-6 103
- 104 104
- Figure 5-7 105
- Figure 5-8 106
- 107
- Configuring Repeater Mode 108
- 109
- 110 110
- Troubleshooting 111
- Basic Functioning 112
- Wireless-Capable Computer 113
- 114 114
- 115
- Problems with Date and Time 116
- Using the Diagnostic Tools 117
- 118 118
- Downloading Debug Information 119
- Figure 6-3 120
- Technical Specifications 121
- Default Factory Settings 122
- Table 0-1 123
- 124 124
- Related Documents 125
- 126 126
- Numerics 127
- 128 128
- Index 129
- 130 130
- Index 131
- 132 132
- Index 133
- 134 134
Relacionado con productos y manuales para Puntos de acceso wlan Netgear WG102
Puntos de acceso wlan Netgear WNDAP330 Guía de usuario
(142 paginas)
(142 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.125 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales