Netgear WG102 Manual de usuario Pagina 122
- Pagina / 134
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
122 |
WG102-500, WGAP150 ProSafe™ 802.11g Wireless Access Point
Default Factory Settings
When you first receive your wireless access point, the default factory settings are set as
shown below. You can restore these defaults with the Reset button on the rear panel (see
“Rear Panel” on page 11).
Maximum Computers Per
Wireless Network
Limited by the amount of wireless network traffic generated by each node.
Typically 20-30 nodes.
Radio Data Rates
802.11b and g 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbps
802.11b,g
Operating Frequencies and
Channels
2.412 ~ 2.462 GHz (North America), Channels 1-11
2.412 ~ 2.472 GHz (Europe including France and Spain, and Japan),
Channels 1-13
802.11 Security 40-bits (64-bit WEP), 104 bits (28-bit WEP), and 128-bits (152-bit WEP)
data encryption; WPA and WPA2
Table 0-1.
Feature Factory Default Settings
User Name (case sensitive) admin
Password (case sensitive) password
Operating Mode Bridge
Access Point Name NETGEAR
Built-in DHCP Server DHCP server enabled, using the default IP address
IP Configuration IP Address: 192.168.0.229
Subnet Mask: 255.255.255.0
Gateway: 0.0.0.0
Network Name (SSID) 16 SSIDs: NETGEAR - 0, NETGEAR - 1, NETGEAR - 2,
and so on to NETGEAR - 15
Broadcast Network Name (SSID) Enabled
WEP/WPA Disabled
MAC Access Control Disabled
Restricting connectivity based on MAC Access
Control List
Disabled
Time Zone Coordinated Universal Time (UTC)
Specification Description
- WG102-500, WGAP150 1
- ProSafe™ 802.11g Wireless 1
- Access Point 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Table of Contents 3
- 4 4
- Table of Contents 5
- Chapter 6 Troubleshooting 6
- Appendix B Related Documents 6
- Introduction 7
- Key Features 8
- 9
- System Requirements 10
- What’s In the Box? 10
- Hardware Description 11
- Table 1-1 12
- 13
- Ethernet Cabling Requirements 14
- 15
- Figure 2-1 16
- Figure 2-2 17
- Figure 2-3 17
- Web Interface Menu 18
- Settings 18
- System > Basic 19
- Configuring IP Settings 20
- Figure 2-7 21
- Table 2-3. PPPoE Settings 22
- Figure 2-8 22
- Configuring LAN Settings 23
- 24 24
- Figure 2-10 25
- 26 26
- Figure 2-11 27
- Figure 2-12 28
- 29
- 30 30
- 31
- 32 32
- 33
- Figure 3-1 34
- Security Profiles 35
- 36 36
- 37
- Figure 3-2 38
- Figure 3-3 39
- Configuring Static WEP 40
- Table 3-3 41
- Figure 3-5 41
- Table 3-2 41
- Table 3-4 42
- Figure 3-6 42
- Table 3-5 43
- Figure 3-7 43
- Figure 3-8 44
- Table 3-6 44
- Table 3-6 45
- Figure 3-9 46
- 47
- 48 48
- WAPI Certificates 49
- Figure 3-11 50
- Figure 3-12 51
- Figure 3-13 52
- Figure 3-14 53
- Figure 3-15 54
- Figure 3-16 55
- Table 3-9. Filter Settings 56
- Figure 3-17 57
- Figure 3-18 58
- Figure 3-19 59
- 60 60
- Managing Your Network 61
- Backing up the Configuration 62
- Restoring the Configuration 62
- 63
- Figure 4-2 64
- 65
- Figure 4-3 66
- Figure 4-4 67
- Viewing the Activity Log 68
- Figure 4-6 69
- Figure 4-7 69
- Viewing System Information 70
- Figure 4-8 71
- Table 4-1 71
- Table 4-1 72
- Table 4-2 73
- Figure 4-9 73
- Viewing Wireless Information 74
- Table 4-4 75
- Figure 4-11 75
- Figure 4-12 75
- Table 4-5 76
- Figure 4-13 77
- Configuring Remote Management 78
- Table 4-7 79
- 80 80
- Figure 4-15 81
- Figure 4-16 82
- Figure 4-17 83
- 84 84
- SNMP Remote Management 85
- Configuring SNMP Communities 86
- Figure 4-20 87
- Figure 4-21 87
- Configuring SNMP Users 88
- Figure 4-22 89
- Figure 4-23 89
- Configuring TR069 Operation 90
- Scheduling Management Tasks 91
- Figure 4-25 92
- 93
- 94 94
- Advanced Configuration 95
- Figure 5-1 96
- Figure 5-2 97
- 98 98
- Figure 5-3 99
- 100 100
- Figure 5-4 101
- Figure 5-5 102
- Figure 5-6 103
- 104 104
- Figure 5-7 105
- Figure 5-8 106
- 107
- Configuring Repeater Mode 108
- 109
- 110 110
- Troubleshooting 111
- Basic Functioning 112
- Wireless-Capable Computer 113
- 114 114
- 115
- Problems with Date and Time 116
- Using the Diagnostic Tools 117
- 118 118
- Downloading Debug Information 119
- Figure 6-3 120
- Technical Specifications 121
- Default Factory Settings 122
- Table 0-1 123
- 124 124
- Related Documents 125
- 126 126
- Numerics 127
- 128 128
- Index 129
- 130 130
- Index 131
- 132 132
- Index 133
- 134 134
Relacionado con productos y manuales para Puntos de acceso wlan Netgear WG102
Puntos de acceso wlan Netgear WNDAP330 Guía de usuario
(142 paginas)
(142 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.086 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales