Netgear WG102 Manual de usuario Pagina 116
- Pagina / 134
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
116 |
WG102-500, WGAP150 ProSafe™ 802.11g Wireless Access Point
PING -n 10 IP address
where IP address is the IP address of a remote device such as your ISP’s DNS server.
If the path is functioning correctly, replies as in the previous section display. If you do not
receive replies:
• Check that your PC has the IP address of your router listed as the default wireless access
point. If the IP configuration of your PC is assigned by DHCP, this information is not
visible in your PC’s Network Control Panel. Verify that the IP address of the router is
listed as the default wireless access point as described in the online document that you
can access from
“Preparing Your Network” in Appendix B.
• Check to see that the network address of your PC (the portion of the IP address specified
by the netmask) is different from the network address of the remote device.
• Check that your cable or DSL modem is connected and functioning.
• If your ISP assigned a host name to your PC, enter that host name as the account name
in the Basic Settings screen.
Using the Reset Button to Restore Factory Default Settings
To use the Reset button (see “Rear Panel” on page 11) to clear all data and restore the
factory default values:
1. Push and hold the Reset button for about five seconds (you may have to push hard).
2. Release the Reset button. A few seconds later, only the power LED of the wireless access
point remains on, indicating that the wireless access point has rebooted. After several
minutes, the factory default configuration will be restored, and the wireless access point will
be ready for use.
Note: After restoring the factory default configuration, the wireless access
point’s default LAN IP address will be 192.168.0.229, the default
login user name will be admin, and the default login password will be
password.
Problems with Date and Time
The Basic screen that is accessible through the Monitor > System > Basic menus choices
displays the current date and time of day. The wireless access point uses the Network Time
Protocol (NTP) to obtain the current time from a Network Time Servers on the Internet that
you specify in the Basic Settings screen (see
“Configuring Basic System Settings” on
- WG102-500, WGAP150 1
- ProSafe™ 802.11g Wireless 1
- Access Point 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Table of Contents 3
- 4 4
- Table of Contents 5
- Chapter 6 Troubleshooting 6
- Appendix B Related Documents 6
- Introduction 7
- Key Features 8
- 9
- System Requirements 10
- What’s In the Box? 10
- Hardware Description 11
- Table 1-1 12
- 13
- Ethernet Cabling Requirements 14
- 15
- Figure 2-1 16
- Figure 2-2 17
- Figure 2-3 17
- Web Interface Menu 18
- Settings 18
- System > Basic 19
- Configuring IP Settings 20
- Figure 2-7 21
- Table 2-3. PPPoE Settings 22
- Figure 2-8 22
- Configuring LAN Settings 23
- 24 24
- Figure 2-10 25
- 26 26
- Figure 2-11 27
- Figure 2-12 28
- 29
- 30 30
- 31
- 32 32
- 33
- Figure 3-1 34
- Security Profiles 35
- 36 36
- 37
- Figure 3-2 38
- Figure 3-3 39
- Configuring Static WEP 40
- Table 3-3 41
- Figure 3-5 41
- Table 3-2 41
- Table 3-4 42
- Figure 3-6 42
- Table 3-5 43
- Figure 3-7 43
- Figure 3-8 44
- Table 3-6 44
- Table 3-6 45
- Figure 3-9 46
- 47
- 48 48
- WAPI Certificates 49
- Figure 3-11 50
- Figure 3-12 51
- Figure 3-13 52
- Figure 3-14 53
- Figure 3-15 54
- Figure 3-16 55
- Table 3-9. Filter Settings 56
- Figure 3-17 57
- Figure 3-18 58
- Figure 3-19 59
- 60 60
- Managing Your Network 61
- Backing up the Configuration 62
- Restoring the Configuration 62
- 63
- Figure 4-2 64
- 65
- Figure 4-3 66
- Figure 4-4 67
- Viewing the Activity Log 68
- Figure 4-6 69
- Figure 4-7 69
- Viewing System Information 70
- Figure 4-8 71
- Table 4-1 71
- Table 4-1 72
- Table 4-2 73
- Figure 4-9 73
- Viewing Wireless Information 74
- Table 4-4 75
- Figure 4-11 75
- Figure 4-12 75
- Table 4-5 76
- Figure 4-13 77
- Configuring Remote Management 78
- Table 4-7 79
- 80 80
- Figure 4-15 81
- Figure 4-16 82
- Figure 4-17 83
- 84 84
- SNMP Remote Management 85
- Configuring SNMP Communities 86
- Figure 4-20 87
- Figure 4-21 87
- Configuring SNMP Users 88
- Figure 4-22 89
- Figure 4-23 89
- Configuring TR069 Operation 90
- Scheduling Management Tasks 91
- Figure 4-25 92
- 93
- 94 94
- Advanced Configuration 95
- Figure 5-1 96
- Figure 5-2 97
- 98 98
- Figure 5-3 99
- 100 100
- Figure 5-4 101
- Figure 5-5 102
- Figure 5-6 103
- 104 104
- Figure 5-7 105
- Figure 5-8 106
- 107
- Configuring Repeater Mode 108
- 109
- 110 110
- Troubleshooting 111
- Basic Functioning 112
- Wireless-Capable Computer 113
- 114 114
- 115
- Problems with Date and Time 116
- Using the Diagnostic Tools 117
- 118 118
- Downloading Debug Information 119
- Figure 6-3 120
- Technical Specifications 121
- Default Factory Settings 122
- Table 0-1 123
- 124 124
- Related Documents 125
- 126 126
- Numerics 127
- 128 128
- Index 129
- 130 130
- Index 131
- 132 132
- Index 133
- 134 134
Relacionado con productos y manuales para Puntos de acceso wlan Netgear WG102
Puntos de acceso wlan Netgear WNDAP330 Guía de usuario
(142 paginas)
(142 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.168 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales