Netgear WC7600 Manual de usuario Pagina 28
- Pagina / 307
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
System Planning and Deployment Scenarios
28
ProSAFE Wireless Controller WC7600
High-Level Configuration Examples
This section includes the following subsections:
• Single Controller Configuration with Basic Profile Group
• Single Controller Configuration with Advanced Profile Groups
• Stacked Controller Configuration
Single Controller Configuration with Basic Profile Group
A basic configuration consists of a single wireless controller that controls a collection of
access points that are organized into the basic default group.
To set up a single wireless controller system with a basic profile group:
Step Configuration Web Management Interface Path
1. Configure the system and network settings of the wireless
controller:
1. Configure the country code of operation.
Configuration > System > General
2. Configure the time settings.
Configuration > System > Time
3. Configure the IP address of the wireless controller.
Configuration > System > IP/VLAN
4. Verify that VLAN 1 is set as the management VLAN and is
marked as untagged.
By default, VLAN 1 an untagged management VLAN.
5. DHCP option 43 (vendor-specific information) must be
enabled on an external DHCP server. If no network DHCP
server is accessible to the access points, configure the
wireless controller’s DHCP server. Specifying an internal
DHCP server on the wireless controller automatically enables
DHCP option 43 with the IP address of the wireless controller.
Configuration > System > DHCP
Server
2. Configure up to eight profiles, and for each profile, do at least the
following:
1. Configure an SSID for wireless access.
Configuration > Profile > Basic
2. Configure the network authentication and data encryption.
3. Assign the VLAN.
4. If necessary for the selected network authentication option,
configure the authentication server.
Configuration > Security > Basic >
Authentication Server
3. Run the Discovery Wizard and add the access points to the
managed access point list.
Access Point > Discovery Wizard
- ProSAFE Wireless Controller 1
- Compliance 2
- Trademarks 2
- Chapter 1 Introduction 3
- Chapter 3 RF Planning 3
- Chapter 13 Troubleshooting 8
- Passwords Requirements 8
- Key Features and Capabilities 10
- Introduction 11
- Hardware Features 12
- Package Contents 12
- Table 1. LED functions 13
- Back Panel Features 14
- Figure 4. Product label 15
- NETGEAR ProSAFE Access Points 16
- Licenses 20
- Maintenance and Support 20
- Scenarios 21
- Profile Group Concepts 23
- Management VLAN 25
- Client VLANs 26
- DHCP Server 26
- RF Planning 41
- To define a building: 42
- Figure 12 43
- Figure 13 43
- To edit a building: 44
- To delete a building: 45
- Figure 14 46
- Figure 15 47
- Figure 16 49
- Figure 17 49
- Overview 51
- Manage the Time Settings 61
- Management VLAN Concepts 62
- Untagged VLAN Concepts 63
- Link Aggregation Concepts 63
- Manage the DHCP Server 65
- 5. Click the Add button 67
- Remove a DHCP Server 69
- Register Your Licenses 70
- To register your licenses: 72
- Manage Certificates 74
- Configure Syslog Settings 77
- To configure alarm actions: 79
- Manage Security Profiles and 82
- Profile Groups 82
- Small WLAN Networks 83
- Large WLAN Networks 84
- Profile Naming Conventions 84
- Add an Advanced Profile Group 91
- Server Groups 104
- Import a MAC List from a File 112
- 00:00:11:11:22:26 113
- 00:00:11:11:22:25 113
- Discover and Manage Access 119
- General Discovery Guidelines 120
- Layer 3 Discovery Guidelines 120
- Number of Controllers Octet 121
- 1 controller 02:04 121
- 2 controllers 02:08 121
- 3 controllers 02:0c 121
- Limitations after Discovery 122
- Points in a Layer 2 Subnet 123
- Manage the Managed AP List 131
- Item Description 132
- Manage Rogue Access Points 140
- Classify Rogue Access Points 142
- 00:00:11:11:22:29 144
- 00:00:11:11:22:28 144
- 00:00:11:11:22:27 144
- Manage Guest Network Access 145
- Configure a Portal 146
- 7. Click the Apply button 148
- User and Account Concepts 150
- Add a Management User 151
- Add a WiFi User 152
- Add a Captive Portal Account 154
- 6. Click the Add button 155
- Add a Captive Portal User 156
- Remove a User or Account 159
- Configure Wireless and QoS 161
- Settings 161
- Concepts 162
- Configure the Radio 162
- Configure Wireless Settings 165
- Profile Group 175
- Configure Channels 177
- Radio Frequency Concepts 180
- WLAN Healing Concepts 181
- Manage the Preferred Bands 186
- Quality of Service Concepts 188
- 8. Click the Apply button 191
- Manage Load Balancing 192
- Configure Load Balancing 193
- Manage Rate Limiting 194
- Manage the Configuration File 199
- Upgrade the Firmware 201
- Reset the Wireless Controller 205
- Manage External Storage 206
- Manage Remote Access 207
- 6. Click the Apply button 208
- Specify Session Time-Outs 209
- Manage the System Logs 209
- Query the System Logs 210
- Save the System Logs 212
- Clear the System Logs 212
- View Alerts and Events 213
- View Radio Frequency Events 214
- View Load-Balancing Events 215
- View Rate-Limit Events 217
- View Redundancy Events 218
- View Stacking Events 218
- Manage Licenses 219
- View Your Licenses 220
- Retrieve Your Licenses 222
- Reboot Access Points 223
- Setting Description 225
- The default number is 69 225
- Stacking Concepts 228
- Configure a Stack 230
- VRRP Redundancy Concepts 237
- Before failover 238
- After failover 239
- VRRP N:1 Redundancy Concepts 241
- Figure 24 243
- Figure 25 243
- Figure 26 244
- Change a Redundant Controller 246
- Remove a Redundancy Group 247
- Its Components 248
- Monitor the Network 249
- To view the Usage screen: 266
- To view the Clients screen: 273
- Does Not Manage 279
- Controller 282
- Wireless Controller Manages 283
- 10. Click the Cancel button 294
- Troubleshooting 295
- Power LED Is Not Lit 296
- Status LED Never Turns Off 296
- Check the Ethernet Cabling 297
- Check the Internet Browser 298
- Resolve Discovery Problems 300
- Resolve Connection Problems 300
- Ping an Access Point 301
- • Factory Default Settings 304
- • Technical Specifications 304
- • Password Requirements 304
- Factory Default Settings 305
- Technical Specifications 305
- Password Requirements 306
Relacionado con productos y manuales para Redes Netgear WC7600
Redes Netgear WG111T Manual de usuario
(49 paginas)
(49 paginas)
Redes Netgear 597E Guía de usuario
(49 paginas)
(49 paginas)
Redes Netgear WG511T Guía de usuario
(48 paginas)
(48 paginas)
Redes Netgear 597E Guía de usuario
(12 paginas)
(12 paginas)
Redes Netgear MA521 Guía de instalación
(2 paginas)
(2 paginas)
Redes Netgear WC7520 Manual de usuario
(213 paginas)
(213 paginas)
Redes Netgear DG834GSP Manual de usuario
(32 paginas)
(32 paginas)
Redes Netgear ProSafe FS728TP Manual de usuario
(248 paginas)
(248 paginas)
Redes Netgear 3G Manual de usuario
(106 paginas)
(106 paginas)
Redes Netgear 7000 Series Manual de usuario
(220 paginas)
(220 paginas)
Redes Netgear 724TP Manual de usuario
(2 paginas)
(2 paginas)
Redes Netgear ProSafe SSL312 Manual de usuario
(122 paginas)
(122 paginas)
Redes Netgear MA401 Manual de usuario
(84 paginas)
(84 paginas)
Redes Netgear DG834GUV5 Manual de usuario
(120 paginas)
(120 paginas)
Redes Netgear WMS5316 Manual de usuario
(66 paginas)
(66 paginas)
Redes Netgear FA511 Guía de instalación
(2 paginas)
(2 paginas)
Redes Netgear MA111v2 Guía de usuario
(83 paginas)
(83 paginas)
Redes Netgear STM300EW-100NAS Manual de usuario
(254 paginas)
(254 paginas)
Redes Netgear 782S Guía de inicio rápido
(48 paginas)
(48 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales