Netgear WNDAP620 Manual de usuario Pagina 126
- Pagina / 172
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Advanced Configuration
126
ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point WNDAP620
Note: You can extend this multipoint bridging configuration by adding
additional wireless access points that are configured in point-to-point
mode for each additional LAN segment. Furthermore, you can
extend the range of the wireless network with NETGEAR wireless
antenna accessories.
Configure the Wireless Access Point to Repeat the Wireless
Signal Using Point-to-Multipoint Bridge Mode
You can configure the wireless access point to repeat the wireless signal, without
communication with other wireless clients. All traffic is sent to the remote or downstream
wireless access point. You can configure up to four security profiles to enable the wireless
access point to repeat the wireless signal for four remote wireless access points. Each
security profile requires a unique name and needs to include the MAC address of the remote
wireless access point. You can configure up to four such security profiles
(NETGEAR-WDS-1, NETGEAR-WDS-2, and so on).
The following figure shows an example in
which AP1, AP2, and AP3 repeat the wireless
signal in point-to-multipoint bridge mode. AP2 requires a security profile for AP1 and another
one for AP3:
Figure 73.
Multipoint
Router
Hub or switch
bridge mode
repeating only
Multipoint
bridge mode
repeating only
Multipoint
bridge mode
repeating only
- ProSafe Premium 3 x 3 1
- Dual-Band Wireless-N 1
- Access Point WNDAP620 1
- Trademarks 2
- Revision History 2
- Contents 3
- Chapter 6 Troubleshooting 5
- What Is in the Box? 7
- System Requirements 8
- Key Features and Standards 8
- Key Features 9
- Introduction 10
- Hardware Description 11
- Rear Panel 13
- Figure 3 14
- Figure 4 14
- 4. Click Regi 15
- 6. Click su 16
- Ethernet Cabling Requirements 18
- Figure 7 21
- Web Management Interface 22
- Figure 10 23
- Figure 11 23
- To configure time settings: 24
- Figure 12 24
- Configure the IPv4 Settings 25
- 3. Click Apply 26
- to save your settings 26
- Figure 14 27
- Figure 15 29
- Figure 16 32
- Ceiling Installation 35
- Wall Installation 38
- Desk Installation 41
- Figure 17 43
- Security Profiles 44
- Form for 802.11b/bg/ng Modes 46
- Form for 802.11a/an Modes 47
- Figure 18 48
- Figure 19 49
- Table 8. Profile settings 49
- Figure 20 50
- Figure 21 53
- Configure Legacy 802.1X 54
- Figure 23 55
- Figure 24 55
- Figure 25 55
- Figure 26 55
- Figure 27 56
- Figure 28 56
- Figure 29 57
- Figure 30 58
- Figure 31 60
- Figure 32 62
- Figure 33 63
- Management and Monitoring 64
- 3. Click App 65
- Figure 35 66
- Figure 36 67
- Web Browser Upgrade Procedure 68
- TFTP Server Upgrade Procedure 69
- Defaults 70
- Restore the Configuration 71
- Settings 71
- Figure 41 72
- Default Configuration 73
- Figure 43 74
- Manage User Accounts 75
- Enable the Syslog Server 76
- View System Information 77
- To view the System screen: 78
- Monitor Wireless Stations 80
- Figure 47 81
- Figure 48 81
- View the Activity Log 83
- Traffic Statistics 83
- Statistics screen: 84
- Figure 51 86
- Figure 52 87
- Figure 53 88
- Figure 54 94
- Most Recent Attacks 96
- Attack Counter 96
- Ad Hoc Networks 97
- Figure 58 98
- Figure 59 100
- Table 28. IPv6 settings 100
- Advanced Configuration 101
- Figure 60 102
- Link Layer Discovery Protocol 103
- To configure STP and VLANs: 104
- Figure 61 104
- Configure Ethernet LLDP 105
- Configure Hotspot Settings 106
- Figure 63 107
- 802.11a/na tab 108
- To configure advanced QoS: 110
- Figure 65 111
- Table 32. EDCA settings 111
- Figure 66 113
- To modify a QoS policy: 117
- To delete a QoS policy: 117
- Configure Wireless Bridging 118
- Figure 67 119
- Figure 68 119
- Figure 69 120
- Figure 70 122
- Figure 71 123
- Figure 72 123
- Figure 73 126
- Figure 74 127
- Figure 75 128
- Troubleshooting 131
- Basic Functioning 132
- Check these items: 133
- Wireless-Capable Computer 134
- Request timed out 136
- Problems with Date and Time 137
- Use the Packet Capture Tool 138
- Supplemental Information 139
- Factory Default Settings 142
- Command-Line Reference 146
- Notification of Compliance 161
- FCC Information to User 163
- FCC Declaration of Conformity 163
- FCC Caution 163
- Radiation Exposure Statement: 164
- Industry Canada 164
- Industrie Canada 164
- Avertissement 165
- Detachable Antenna Usage 165
- Numerics 166
Relacionado con productos y manuales para Puntos de acceso wlan Netgear WNDAP620
(70 paginas)
Puntos de acceso wlan Netgear WAG102 Manual de usuario
(102 paginas)
(102 paginas)
Puntos de acceso wlan Netgear 802.11g Manual de usuario
(108 paginas)
(108 paginas)
Puntos de acceso wlan Netgear WG602v2 Guía de usuario
(122 paginas)
(122 paginas)
Puntos de acceso wlan Netgear MP115 Guía de usuario
(78 paginas)
(78 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales