Netgear Switch L3 Manual de usuario Pagina 96
- Pagina / 271
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
7000 Series L3 Managed Switch Reference Manual for Software v2.0
7-42 Switching Commands
config igmpsnooping groupmembershipinterval
This command sets the IGMP Group Membership Interval time on the system. The Group
Membership Interval time is the amount of time in seconds that a switch will wait for a report from
a particular group on a particular interface before deleting the interface from the entry. This value
must be greater than the IGMP Maximum Response time value. The range is 1 to 3600 seconds.
Default 260 seconds
Format config igmpsnooping groupmembershipinterval <1-3600>
config igmpsnooping maxresponse
This command sets the IGMP Maximum Response time on the system. The Maximum Response
time is the amount of time in seconds that a switch will wait after sending a query on an interface
because it did not receive a report for a particular group in that interface. This value must be less
than the IGMP Query Interval time value. The range is 1 to 3600 seconds.
Default 10 seconds
Format config igmpsnooping maxresponse <1-3600>
config igmpsnooping mcrtrexpiretime
This command sets the Multicast Router Present Expiration time on the system. This is the amount
of time in seconds that a switch will wait for a query to be received on an interface before the
interface is removed from the list of interfaces with multicast routers attached. The range is 0 to
3600 seconds. A value of 0 indicates an infinite timeout, i.e. no expiration.
Default 0
Format config igmpsnooping mcrtrexpiretime <0-3600>
config igmpsnooping interface mode
This command enables or disables IGMP Snooping on a selected interface. The <slot.port/all>
parameter identifies the interface on which to configure the mode. If an interface which has IGMP
Snooping enabled is enabled for routing or is enlisted as a member of a LAG, IGMP Snooping
functionality will be disabled on that interface. IGMP Snooping functionality will subsequently be
re-enabled if routing is disabled or LAG membership is removed from an interface that has IGMP
Snooping enabled.
Default disable
- 7000 Series L3 Managed 1
- Switch Reference Manual for 1
- Software v2.0 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Contents 5
- Chapter 1 21
- About This Guide 21
- Typographical Conventions 22
- Special Message Formats 22
- How to Navigate this Manual 23
- How to Print this Manual 24
- Chapter 2 25
- Chapter 3 27
- Chapter 4 31
- How to Log In to the GSM73xx 32
- Interactive Switch Image 34
- System-Wide Popup Menus 36
- Port-Specific Popup Menus 37
- Chapter 5 39
- Command Line Interface Syntax 39
- CLI Command Values 40
- CLI Command Conventions 40
- CLI Annotations 41
- Chapter 6 43
- Quick Startup 43
- Physical Port Data 44
- User Account Management 44
- IP Address 45
- 6-4 Quick Startup 46
- The types are: 47
- Downloading from TFTP Server 48
- Factory Defaults 48
- Basic Configuration Examples 49
- RIP and OSPF VLAN Routing 50
- Quick Startup 6-9 51
- 6-10 Quick Startup 52
- VLAN Example 53
- SOLUTION 1 54
- SOLUTION 2 54
- Chapter 7 55
- Switching Commands 55
- 7-2 Switching Commands 56
- Switching Commands 7-3 57
- 7-4 Switching Commands 58
- Switching Commands 7-5 59
- 7-6 Switching Commands 60
- Switching Commands 7-7 61
- 7-8 Switching Commands 62
- Switching Commands 7-9 63
- 7-10 Switching Commands 64
- Switching Commands 7-11 65
- 7-12 Switching Commands 66
- Switching Commands 7-13 67
- 7-14 Switching Commands 68
- Management Commands 69
- 7-16 Switching Commands 70
- Switching Commands 7-17 71
- 7-18 Switching Commands 72
- Switching Commands 7-19 73
- 7-20 Switching Commands 74
- Switching Commands 7-21 75
- 7-22 Switching Commands 76
- Switching Commands 7-23 77
- Device Configuration Commands 78
- Switching Commands 7-25 79
- 7-26 Switching Commands 80
- Switching Commands 7-27 81
- 7-28 Switching Commands 82
- Switching Commands 7-29 83
- 7-30 Switching Commands 84
- Switching Commands 7-31 85
- 7-32 Switching Commands 86
- Switching Commands 7-33 87
- 7-34 Switching Commands 88
- Switching Commands 7-35 89
- 7-36 Switching Commands 90
- Switching Commands 7-37 91
- 7-38 Switching Commands 92
- Switching Commands 7-39 93
- 7-40 Switching Commands 94
- Switching Commands 7-41 95
- 7-42 Switching Commands 96
- Switching Commands 7-43 97
- 7-44 Switching Commands 98
- Switching Commands 7-45 99
- 7-46 Switching Commands 100
- Switching Commands 7-47 101
- 7-48 Switching Commands 102
- Spanning Tree Commands 103
- 7-50 Switching Commands 104
- Switching Commands 7-51 105
- 7-52 Switching Commands 106
- Switching Commands 7-53 107
- 7-54 Switching Commands 108
- Switching Commands 7-55 109
- 7-56 Switching Commands 110
- Switching Commands 7-57 111
- 7-58 Switching Commands 112
- Switching Commands 7-59 113
- 7-60 Switching Commands 114
- Switching Commands 7-61 115
- 7-62 Switching Commands 116
- Security Commands 117
- 7-64 Switching Commands 118
- Switching Commands 7-65 119
- 7-66 Switching Commands 120
- 7-68 Switching Commands 122
- Switching Commands 7-69 123
- 7-70 Switching Commands 124
- Switching Commands 7-71 125
- 7-72 Switching Commands 126
- Switching Commands 7-73 127
- 7-74 Switching Commands 128
- Switching Commands 7-75 129
- 7-76 Switching Commands 130
- Switching Commands 7-77 131
- 7-78 Switching Commands 132
- System Utilities 133
- 7-80 Switching Commands 134
- TFTP Upload Example: 135
- 7-82 Switching Commands 136
- Switching Commands 7-83 137
- 7-84 Switching Commands 138
- Switching Commands 7-85 139
- 7-86 Switching Commands 140
- Chapter 8 141
- Routing Commands 141
- 8-2 Routing Commands 142
- Routing Commands 8-3 143
- 8-4 Routing Commands 144
- Routing Commands 8-5 145
- 8-6 Routing Commands 146
- Routing Commands 8-7 147
- 8-8 Routing Commands 148
- Routing Commands 8-9 149
- 8-10 Routing Commands 150
- Routing Commands 8-11 151
- 8-12 Routing Commands 152
- Routing Commands 8-13 153
- 8-14 Routing Commands 154
- Routing Commands 8-15 155
- 8-16 Routing Commands 156
- Routing Commands 8-17 157
- 8-18 Routing Commands 158
- Routing Commands 8-19 159
- 8-20 Routing Commands 160
- Routing Commands 8-21 161
- 8-22 Routing Commands 162
- Routing Commands 8-23 163
- 8-24 Routing Commands 164
- Routing Commands 8-25 165
- 8-26 Routing Commands 166
- Routing Commands 8-27 167
- 8-28 Routing Commands 168
- Routing Commands 8-29 169
- 8-30 Routing Commands 170
- Routing Commands 8-31 171
- 8-32 Routing Commands 172
- Routing Commands 8-33 173
- 8-34 Routing Commands 174
- Routing Commands 8-35 175
- 8-36 Routing Commands 176
- Routing Commands 8-37 177
- 8-38 Routing Commands 178
- Chapter 9 179
- General Commands 180
- Class Commands 181
- keyword <class 188
- number <class 188
- <add/remove> 189
- Policy Commands 192
- <policyname> 194
- <policyname> 195
- conform send 199
- exceed markdscp 199
- nonconform mark 201
- nonconform send 202
- Service Commands 205
- <slot.port/all> 206
- Show Commands 207
- Class Name 208
- <slot.port> <in/ 212
- <slot.port> [in/ 213
- [in/out] 215
- Chapter 10 217
- ACL Commands 217
- Config Commands 218
- ACL Commands 10-3 219
- 10-4 ACL Commands 220
- ACL Commands 10-5 221
- <tosmask> of a2 (hex) 221
- 10-6 ACL Commands 222
- ACL Commands 10-7 223
- ACL to add 224
- Appendix A 225
- Cabling Guidelines 225
- Category 5 Cable 226
- Twisted Pair Cables 227
- Patch Panels and Cables 228
- Cabling Guidelines A-5 229
- Near End Cross Talk (NEXT) 230
- Patch Cables 230
- Cabling Guidelines A-7 231
- Conclusion 232
- Appendix B 233
- Appendix C 237
- Glossary 237
- Joint Test Action Group 249
- Glossary C-27 263
- C-28 Glossary 264
© 2020, manymanuals.es. Todos los derechos reservados | 0.114 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales